Bewise Inc. www.tool-tool.com Reference source from the internet.
Name
PCB Size (mm)
WTX
356×425
AT
350×305
Baby-AT
330×216
BTX
325×266
ATX
305×244
LPX
330×229
NLX
254×228
microATX
244×244
DTX
244×203
FlexATX
229×191
Mini-DTX
203×170
EBX
203×146
microATX (Min.)
171×171
Mini-ITX
170×170
EPIC (Express)
165×115
ESM
149×71
Nano-ITX
120×120
COM Express
125×95
ESMexpress
125×95
ETX / XTX
114×95
Pico-ITX
100×72
PC/104 (-Plus)
96×90
mobile-ITX
75×45
The ATX (for Advanced Technology eXtended) form factor was created by Intel in 1995. It was the first big change in computer case and motherboard design in many years. ATX overtook AT completely as the default form factor for new systems. ATX addressed many of the AT form factor's annoyances that had frustrated system builders. Other standards for smaller boards (including microATX, FlexATX and mini-ITX) usually keep the basic rear layout but reduce the size of the board and the number of expansion slot positions. In 2003, Intel announced the BTX standard, intended as a replacement for ATX. As of 2009[update] the ATX form factor remains the industry standard for do-it-yourselfers; BTX has however made inroads into pre-made systems, being adopted by computer makers like Dell, Gateway, and HP.
The official specifications were released by Intel in 1995, and have been revised numerous times since, the most recent being version 2.2,[1] released in 2004.
A full size ATX board is 305 mm wide by 244 mm deep (12" x 9.6" ). This allows many ATX form factor chassis to accept microATX boards as well.
[edit] Power supply
ATX form motherboards became increasingly popular because of their advantages over older AT motherboards.
[edit] Main changes from AT design
[edit] Power switch
AT-style computer cases had a power button that was directly connected to the system computer power supply (PSU). The general configuration was a double-pole latching mains voltage switch with the four pins connected to wires from a four-core cable. The wires were either soldered to the power button (making it difficult to replace the power supply if it failed) or blade receptacles were used.
Typical ATX power supply
Interior view of an ATX power supply.
An ATX power supply does not directly connect to the system power button, allowing the computer to be turned off via software. However, many ATX power supplies have a manual switch on the back to ensure the computer is truly off and no power is being sent to the components. With this switch on, energy still flows to the components even when the computer appears to be "off." This is known as soft-off or standby and can be used for remote wake up through Wake-on-Ring or Wake-on-LAN, but is generally used to power on the computer through a front switch.
[edit] Power connection to the motherboard
The power supply's connection to the motherboard was changed. Older AT power supplies had two similar connectors that could be accidentally switched, usually causing short-circuits and irreversible damage to the motherboard. ATX used one large, keyed connector instead, making a reversed connection very difficult. The new connector also provided a 3.3 volt source, removing the need for motherboards to derive this voltage from one of the other power rails. Some motherboards, particularly late model AT form factor offerings, supported both AT and ATX PSUs.
If you are not working with an ATX motherboard you can only turn on the power by shorting the green wire from the ATX connector to a black wire on the connector (or ground), since it is the motherboard's power switch which the ATX PSU uses. This means that an old PC power supply can be used for tasks other than powering a PC, but one must be careful to observe the minimum load requirements of the PSU.
[edit] Airflow
ATX was originally designed with the power supply drawing air into the case and exhausting it down onto the motherboard. The plan was to deliver cool air directly to the CPU's and power regulation circuitry's location, which was usually at the top of the motherboard in ATX designs. This was not particularly useful for a variety of reasons. Early ATX systems simply didn't have processors or components with thermal output that required special cooling considerations. Later ATX systems with significantly greater heat output would not be aided in cooling by a power supply, because it would be delivering its often significantly heated exhaust into the case. As a result, the ATX specification was changed to make PSU airflow optional.[1]
[edit] ATX power supply revisions
[edit] Original ATX
ATX, introduced in late 1995, defined three types of power connectors:
- 4-pin peripheral connector (commonly but inaccurately known as "MOLEX")—transferred directly from AT standard
- 4-pin floppy connector—transferred directly from AT standard
- 20-pin main motherboard connector—new to the ATX standard
The power distribution specification defined that most of PSU's power should be provided on 5V and 3.3V rails, because most of the electronic components (CPU, RAM, chipset, PCI, AGP and ISA cards) used 5V or 3.3V for power supply. The 12V rail was only used by fans and motors of peripheral devices (HDD, FDD, CD-ROM, etc.).
The original ATX power supply specification remained mostly unrevised until year 2000.
[edit] ATX12V 1.x
While designing the Pentium 4 platform in 1999/2000, the standard 20-pin ATX power connector was deemed inadequate to supply increasing electrical load requirements. So, ATX was significantly revised into ATX12V 1.0 standard (that is why ATX12V 1.x is sometimes inaccurately called ATX-P4). ATX12V 1.x was also adopted by Athlon XP and Athlon 64 systems.
[edit] ATX12V 1.0
The main changes and additions in ATX12V 1.0 (released in February 2000) were:
- An extra 4-pin, 12-volt connector to power the CPU. Formally called the "+12 V Power Connector", this is commonly referred to as the P4 connector because this was first needed to support the Pentium 4 processor. (Older processors were powered from the 5V rail.)
- A supplemental 6-pin AUX connector providing additional 3.3V and 5V supplies to the motherboard, if it needed it. Although it was provided by every ATX12V 1.x PSU (as required per standard), it was rarely required by motherboards.
- Increased the power on the 12V rail (power on 5V and 3.3V rails remained mostly the same).
[edit] ATX12V 1.1
This is a minor revision from August 2000. The power on 3.3V rail was slightly increased, among other much lesser changes.
[edit] ATX12V 1.2
A relatively minor revision from January 2002. The only significant change was that the −5V rail was no longer required (it became optional). This voltage was very rarely used, only on some old systems with some ISA add-on cards.
[edit] ATX12V 1.3
Introduced in April 2003 (a month after 2.0). Lot of relatively minor changes. Some of them are:
- Slightly increased the power on 12V rail.
- Defined minimal required PSU efficiencies for light and normal load.
- Defined acoustic levels.
- Introduction of Serial ATA power connector (but defined as optional).
[edit] ATX12V 2.x
ATX12V 2.x brought a very significant design change regarding power distribution. When analyzing the then-current PC architectures' power demands, it was determined that it would be much easier (both from economical and engineering perspectives) to power most PC components from 12V rails, instead of from 3.3V and 5V rails.
[edit] ATX12V 2.0
The above conclusion was incorporated in ATX12V 2.0 (introduced in February 2003), which defined quite different power distribution from ATX12V 1.x:
- The main ATX power connector was extended to 24 pins (it is backwards compatible). The extra four pins provide one additional 3.3V, 5V and 12V circuit.
- The 6-pin AUX connector from ATX12V 1.x was removed because the extra 3.3V and 5V circuits which it provided are now incorporated in the 24-pin main connector.
- Most power is now provided on 12V rails. The standard specifies that two independent 12V rails (12V2 for the 4 pin connector and 12V1 for everything else) with independent overcurrent protection are needed to meet the power requirements safely (some very high power PSUs have more than two rails, recommendations for such large PSUs are not given by the standard).
- The power on 3.3V and 5.V rails was significantly reduced.
- Serial ATA power cable is required.
- Many other specification changes and additions.
(20-pin omits the last 4: 11, 12, 23 and 24)
Color
Signal
Pin
Pin
Signal
Color
Orange
+3.3 V
1
13
+3.3V
Orange
+3.3 V sense
Brown
Orange
+3.3 V
2
14
−12 V
Blue
Black
Ground
3
15
Ground
Black
Red
+5 V
4
16
Power on
Green
Black
Ground
5
17
Ground
Black
Red
+5 V
6
18
Ground
Black
Black
Ground
7
19
Ground
Black
Grey
Power good
8
20
−5 V (optional)
White
Purple
+5 V standby
9
21
+5 V
Red
Yellow
+12 V
10
22
+5 V
Red
Yellow
+12 V
11
23
+5 V
Red
Orange
+3.3 V
12
24
Ground
Black
[edit] ATX12V v2.01
This is a minor revision from June 2004. The −5V rail was completely removed from the specification.
[edit] ATX12V v2.1
This is a minor revision from March 2005. The power was slightly increased on all rails. Efficiency requirements changed.
[edit] ATX12V v2.2
Another minor revision, the main change was a call for higher-quality connectors on the motherboard power connectors.
[edit] ATX power supply derivatives
[edit] AMD GES
This is an ATX12V power supply derivative made by AMD to power its Athlon MP (dual processor) platform. It was used only on high-end Athlon MP motherboards. It has a special 8-pin supplemental connector for motherboard, so an AMD GES PSU is required for such motherboards (those motherboards will not work with ATX(12V) PSUs).
[edit] EPS12V
Defined in SSI, and used by some (Xeon and Opteron) systems[dubious – discuss]. It has 24 pin main connector, 8 pin secondary connector, optional 4 pin tertiary connector.
[edit] Recent specification changes and additions
Because video card power demands have dramatically increased over the 2000s, some high-end graphics cards have power demands that exceed AGP or PCIe slot capabilities. For these cards, supplementary power was delivered through a standard 4-pin peripheral or floppy power connector. Midrange and high-end PCI Express-based video cards manufactured after 2004 typically use a standard 6 or 8-pin PCIe power connector directly from the PSU.
[edit] Interchanging old/new systems with old/new PSUs
Although the ATX power supply specifications are all vertically compatible in both ways (both electrically and physically), it is not wise to mix old motherboards/systems with new PSU's, and vice versa.
There are two main reasons for this:
- The power distribution biases across 3.3V, 5V and 12V rails are very different between older and newer ATX PSU designs, as well as between older and newer PC system designs.
- Older PSUs may not have connectors which are required for newer PC systems to properly operate.
This is a practical guidance what to mix and what not to mix:
- Older systems (until Pentium 4 and Athlon XP platforms) were designed to draw most power from 5V and 3.3V rails.
- Pentium 4 and Athlon XP systems draw much more from 12V rail, instead from 5V and 3.3V rails.
- Newer systems (Athlon 64, Core Duo etc.) draw most power from 12V rails.
- Original ATX PSUs have power distribution designed for pre-P4/XP PCs. They lack the supplemental 4-pin 12-volt connector for the CPU, so they simply cannot be used with P4/XP era or newer motherboards (adapters do exist but power drain on the 12V rail must be checked very carefully if using them).
- ATX12V 1.x PSUs have power distribution designed for P4/XP PCs, but they are also greatly suitable for older PCs, since they give plenty of power (relative to old PCs' needs) both on 12V and on 5V/3.3V. Some of them might not have the -5V rail which is needed for some special add-in ISA cards. It is not recommended to use ATX12V 1.x PSUs on ATX12V 2.x motherboards because those systems require much more power on 12V, and much less on 3.3V/5V than ATX12V PSUs provide.
- ATX12V 2.x PSUs have power distribution designed for late P4/XP PCs and for Athlon 64 and Core Duo PCs. They can be used with earlier P4/XP PCs, but the power distribution will be significantly suboptimal, so a more powerful ATX12V 2.0 PSU should be used to compensate for that discrepancy. ATX12V 2.x PSUs can also be used with pre-P4/XP systems, but the power distribution will be greatly suboptimal (12V rails will be mostly unused, while the 3.3V/5V rails will be overloaded), so this is not recommended.
Special note: Proprietary brand-name or high-end workstation/server designs do not fit into these guidelines. They usually require an exactly matching power supply unit.
[edit] Issues with Dell power supplies
Older Dell computers, particularly those from the Pentium II and III times, are notable for using proprietary power wiring on their power supplies and motherboards. While the motherboard connectors appear to be standard ATX, and will actually fit a standard power supply, they are not compatible. Not only have wires been switched from one location to another, but the number of wires for a given voltage has been changed. Thus, the pins cannot simply be rearranged.[2]
The change affects not only 20-pin ATX connectors, but also auxiliary 6-pin connectors. Modern Dell systems may use standard ATX connectors.[3] Dell PC owners should be careful when attempting to mix non-Dell motherboards and power supplies, as it can cause damage to the power supply or other components. If the power supply color coding on the wiring does not match ATX standards, then it is probably proprietary. Wiring diagrams for Dell systems are usually available on Dell's support page.
[edit] Connectors
ATX I/O plates
On the back of the system, some major changes were made. The AT standard had only a keyboard connector and expansion slots for add-on card backplates. Any other onboard interfaces (such as serial and parallel ports) had to be connected via flying leads to connectors which were mounted either on spaces provided by the case or brackets placed in unused expansion slot positions. ATX allowed each motherboard manufacturer to put these ports in a rectangular area on the back of the system, with an arrangement they could define themselves (though a number of general patterns depending on what ports the motherboard offers have been followed by most manufacturers). Generally the case comes with a snap out panel, also known as an I/O plate, reflecting one of the common arrangements. If necessary, I/O plates can be replaced to suit the arrangement on the motherboard that is being fitted and the I/O plates are usually included when purchasing a motherboard. Panels were also made that allowed fitting an AT motherboard in an ATX case.
ATX also made the PS/2-style mini-DIN keyboard and mouse connectors ubiquitous. AT systems used a 5-pin DIN connector for the keyboard, and were generally used with serial port mice (although PS/2 mouse ports were also found on some systems). Many modern motherboards are phasing out the PS/2-style keyboard and mouse connectors in favor of the more modern Universal Serial Bus. Other legacy connectors that are slowly being phased out of modern ATX motherboards include 25-pin parallel ports and 9-pin RS-232 serial ports. In their place are on-board peripheral ports such as Ethernet, FireWire, eSATA, audio ports (both analog and S/PDIF), video (analog D-sub, DVI, or HDMI), and extra USB ports.
[edit] Variants
There exist several ATX-derived form factors that use the same power supply, mountings and basic back panel arrangement, but set different standards for the size of the board.
ATX Scale Reference
width
length
color in image
FlexATX
9 inches (228.6 mm)
7.5 inches (190.5 mm)
microATX and EmbATX
9.6 inches (243.8 mm)
9.6 inches (243.8 mm)
Mini ATX
11.2 inches (284 mm)
8.2 inches (208 mm)
Standard ATX
12 inches (304.8 mm)
9.6 inches (243.8 mm)
EATX (extended ATX)
12 inches (304.8 mm)
13 inches (330.2 mm)
WTX (workstation ATX)
14 inches (355.6 mm)
16.75 inches (425.4 mm)
[edit] Prototypes
In CeBIT 2008, Foxconn unveiled a Foxconn F1 motherboard prototype, the same length as a standard ATX motherboard, but wider to accommodate 10 slots.[2] In January 2008, Lian Li unveiled Armorsuit PC-P80 case with 10 slots designed for the motherboard.[3]
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、複合式再研磨機、PCD地板專用企口鑽石組合刀具、NSK高數主軸與馬達、專業模具修補工具-氣動與電動、粉末造粒成型機、主機版專用頂級電桿、PCD V-Cut刀、捨棄式圓鋸片組、粉末成型機、主機版專用頂級電感、’汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具、銑刀與切斷複合再研磨機、銑刀與鑽頭複合再研磨機、銑刀與螺絲攻複合再研磨機等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool.com / FAX:+886 4 2471 4839 N.Branch 5F,No.460,Fu Shin North Rd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,Taipao City,Chiayi Hsien,Taiwan
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、hss drill’Фрезеры’Carbide drill、High speed steel、Compound Sharpener’Milling cutter、INDUCTORS FOR PCD’CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool. INDUCTORS FOR PCD . POWDER FORMING MACHINE ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’POWDER FORMING MACHINE’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、Staple Cutter’PCD diamond cutter specialized in grooving floors’V-Cut PCD Circular Diamond Tipped Saw Blade with Indexable Insert’ PCD Diamond Tool’ Saw Blade with Indexable Insert’NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills’end mill grinder’drill grinder’sharpener、Stub roughing end mills、Dovetail milling cutters、Carbide slot drills、Carbide torus cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot drills、Mould cutter、Tool manufacturer.
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（７）医療用品エンド・ミル設計
弊社の製品の供給調達機能は：
（４）オートメーション整備調達
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
Bewise Inc. talaşlı imalat sanayinde en fazla kullanılan ve üç eksende (x,y,z) talaş kaldırabilen freze takımlarından olan Parmak Freze imalatçısıdır. Çok geniş ürün yelpazesine sahip olan firmanın başlıca ürünlerini Karbür Parmak Frezeler, Kalıpçı Frezeleri, Kaba Talaş Frezeleri, Konik Alın Frezeler, Köşe Radyüs Frezeler, İki Ağızlı Kısa ve Uzun Küresel Frezeler, İç Bükey Frezeler vb. şeklinde sıralayabiliriz.
BW специализируется в научных исследованиях и разработках, и снабжаем самым высокотехнологичным карбидовым материалом для поставки режущих / фрезеровочных инструментов для почвы, воздушного пространства и электронной индустрии. В нашу основную продукцию входит твердый карбид / быстрорежущая сталь, а также двигатели, микроэлектрические дрели, IC картонорезальные машины, фрезы для гравирования, режущие пилы, фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки форм для шлицевого вала / звездочки роликовой цепи, и специальные нано инструменты. Пожалуйста, посетите сайт www.tool-tool.com для получения большей информации.
BW is specialized in R&D and sourcing the most advanced carbide material with high-tech coating to supply cutting / milling tool for mould & die, aero space and electronic industry. Our main products include solid carbide / HSS end mills, micro electronic drill, IC card cutter, engraving cutter, shell end mills, cutting saw, reamer, thread reamer, leading drill, involute gear cutter for spur wheel, rack and worm milling cutter, thread milling cutter, form cutters for spline shaft/roller chain sprocket, and special tool, with nano grade. Please visit our web www.tool-tool.com for more info.
