Bewise Inc. www.tool-tool.com Reference source from the internet.
燃油喷油装置
fuel injection equipment
燃油喷射泵
fuel injection pump
滚轮式燃油喷射泵
roll fuel injection pump
凸轮轴式燃油喷射泵
camshaft fuel injection pump
直列式燃油喷射泵
in-line fuel injection pump
伺服式燃油喷射泵
servo fuel injection pump
底部突缘安装燃油喷射泵
base flanged mounted fuel injection pump
上部安装燃油喷射泵
high flanged-mounted fuel injection pump
侧向安装燃油喷射泵
side-mounted fuel injection pump
端部突缘安装式燃油喷射泵
end flange-mounted fuel injection pump
V形燃油喷射泵
vee fuel injection pump
脉动式燃油喷射泵
jerk fuel injection pump
螺纹安装燃油喷射泵
screw-mounted fuel injection pump
蓄能式燃油喷射泵
accumulator fuel injection pump
往复式燃油喷射泵
reciprocating fuel injection pump
驱动轴式燃油喷射泵
driveshaft fuel injection pump
单缸式燃油喷射泵
single cylinder fuel injection pump
圆柱式燃油喷射泵
cylindrical fuel injection pump
旋转式燃油喷射泵
rotary fuel injection pump
分配式燃油喷射泵
distributor fuel injection pump
多缸燃油喷射泵
multicylinder fuel injection pump
框架安装式燃油喷射泵
cradle mounted injection pump
喷油始点
fuel injection beginning
喷油终点
fuel injection end
喷油持续角
fuel injection duration angle
喷油延迟
injection delay
引燃喷射
pilot injection
启喷压力
injection starting pressure
峰值喷油扭矩
peak injection torque
峰值喷油压力
peak injection pressure
喷油泵油缸数目
number of cylinders of an injection pump
无气喷射
solid injection
喷射正时
injection timing
集中喷射
group injection
喷油器
injector
整体式喷油器
unit injector
喷嘴
nozzle
轴针式喷嘴
pintle type nozzle
环槽式喷嘴
annular slot nozzle
孔式喷嘴
hole type nozzle
长杆喷嘴
long stem nozzle
孔板式喷嘴
orifice plate nozzle
开式喷嘴
open nozzle
闭式喷嘴
closed nozzle
喷油提前器
timing advance unit
喷射泵壳体
injection pump housing
针阀
needle
芯轴
central spindle
喷嘴壳体
nozzle body
针阀升程
needle lift
喷嘴盖形螺母
nozzle cap nut
喷油器壳体
nozzle holder
突缘安装喷油器壳体
flanged-mounted injection nozzle holder
燃油喷射泵传动装置
transmision of an injection pump
喷嘴锥体
nozzle hole cone
柱塞
plunger
柱塞套
barrel
柱塞行程
plunger stroke
喷孔
spray orifice
海拔控制器
altitude control
提前器飞锤
flyweight
喷孔长径比
ratio of nozzle hole length nozzle diameter
喷嘴液动力特性
nozzle hydrokinetic characteristics
动态相位
dynamic phase
喷孔面积
nozzle hole area
喷嘴流通特性
nozzle flow characteristic
喷油背压
injection back pressure
高压油管
high pressure pipe
平均喷油扭矩
mean injection torque
喷油总效率
overall pumping efficiency
峰值喷油压力
injection peak pressure
预行程
prestroke
收缩行程
retraction stroke
燃油箱
fuel tank
油箱盖
fuel tank
油位表
fuel level gauge
注油控制装置
fill control system
汽油箱
gasoline tank( petrol tank)
汽油供给管
gasoline feed pipe
加油管
filler tube
放油螺塞
drain plug
吸油管
suction pipe
刚性燃油管
rigid fuel pipe
进油孔
fuel feed hole
供油管
supply pipe
通气管
bleeding pipe
通气管
bleeding pipe
泄油阀
spill valve
泄油孔口
spill port
进油阀
inlet valve
最大油量限制器
maximum fuel stop
滴油
dribble
燃油表
fuel gauge
输油泵
feed pump
燃油泵
fuel pump
附装燃油箱中的电动燃油泵
tank-mounted eletric fuel pump
机械式燃油泵
mechanical fuel pump
膜片式燃油泵
diaphragm fuel supply pump
叶片式供油泵
vane fuel supply pump
活塞式输油泵
piston type fuel supply pump
齿轮式输油泵
gear fuel supply pump
电动燃油泵
eletric fuel pump
带真空泵的汽油泵
vacuum pump with fuel pump
起动加油器
primer
起动给油杆
primer lever
燃油泵上体
fuel pump body
燃油泵下体
fuel pump base
燃油泵盖
bowl cover
进油口接头
fuel inlet neck
出油口接头
fuel discharge port
输出阀
delivery valve
泵油元件
pump element
回油阀部件
fuel return valve assembly
化油器
carburetor
化油器系统
carburetor circuit
简单化油器
elementary carburetor
单腔化油器
single-barrel carburetor
双腔并动化油器
two-barrel dual carburetor
双腔分动化油器
two-barrel duplex carburetor
四腔化油器
four-barrel carburetor
上吸式化油器
updaught carburetor
下吸式化油器
downdraught carburetor
平吸式化油器
horizontal carburetor
侧吸式化油器
side-draft-carburetor
高海拔补偿式化油器
altitude compensating carburetor
化油器附加器
adaptor carburetor
双腔式化油器
twin-choke carburetor
固定喉管式化油器
fixed venturi carburetor
可变喉管化油器
variable venturi carburetor
化油器接头
carburetor adaptor
阻风门
choke valve
阻风活塞
choke piston
阻风板
choke plate
自动阻风门
automatic choke
阻风门拉钮
choke button
电控自动阻风门
electric-assisted choke
阻风管
choke tube
喉管
venturi
双重或三重喉管
double & triple venturi
阻风门拉线
choke cable
化油器小喉管
booster venturi
浮子系
float system
浮子
float
环形浮子
annular float
同心式浮子
concentric float
浮子支销
float hinge pin
浮子针阀
float needle valve
阀针
valve needle
浮子油面
float level
浮子臂
float arm
侧置浮子室式
side float type
怠速阀
idle valve
怠速针阀
idle needle
省油器
economizer
省油器阀
economizer valve
辅助空气阀
auxiliary air-valve
加速油井
accelerating well
加速泵
accelerating pump
加速泵喷嘴
accelerating pump nozzle
油门
throttle
手油门
hand throttle
节气门操纵手柄
throttle control lever
真空加浓器
vacuum booster
加浓器
excess fuel device
量孔体
jet block
怠速量孔
idle metering jet
主量孔
main metering jet
剂量阀活塞
dosage valve piston
空气量孔
air jet
燃油滤清器
fuel filter
沉淀杯
sediment bowl
串联过滤器
in-line filter
燃油箱内装过滤器
in-tank filter
调速器
governor
飞球式调速器
flyball governor
调速器
governor
飞球式调速器
flyball governor
液压调速器
hydraulic governor
真空转速调速器
vacuum speed governor
惯性调速器
inertia governor
离心调速器
centrifugal governor
调速器重锤
governor weight
空气滤清器及进排气系统
air cleaner and intake and exhaust sytem
空气滤清器
air filter
冲压式空气滤清器
ram air clearner
恒温控制式空气滤清器
thermostatic controlled air cleaner
油浴式空气滤清器
oil bath air cleaner
纸质空气滤 清器
paper air clearner
旋流管式空气滤清器
swirl tube air filter
滤清器滤芯
filter element
空气滤清器壳体
air filter housing
空气滤清器盖
air filter cover
滤清器密封圈
filter seal ring
滤网
sieve
滤纸盘或膜
filter paper disc or membrane
进气和排气系统
intake and exhaust system
排气管
exhaust pipe
排气抽气管
exhaust extraction duct
扫气泵
scavenging pump
进气预热装置
intake preheater
进气歧管
intake manifold
进气歧管真空度
intake manifold vacuum
冷式进气歧管
cold manifold
冲压式进气歧管
ram intake manifold
排气歧管
exhaust manifold
脉冲式排气歧管
pulse exhaust manifold
等压排气歧管
constant pressrue exhaust manifold
排气歧管热量控制阀
exhaust manifold heat control valve
超高度歧管
high-rise manifold
升温横跨管道
heat crossover
排气横跨管道
exhaust crossover
预热点
hot spot
阻风门加热器
choke heater
热空气导流管
hot air duct
隔热板
heat shield
排气再循环阀
exhaust -gas-recirculation
消声器
silencer
进气消声器
intake silencer
排气消声器
exhaust silencer
金属垫片式消声器
steel pack muffler
玻璃丝消声器
glass pack muffler
空洞消声器
gutted muffler
前排气管
front exhaust pipe
尾管
tail pipe
消声器联接管
intermediate pipe
热空气管
hot air pipe
曲轴箱通风管
crankcase bleed pipe
隔声罩
acoustic hood
进气消声器元件
silencer element
真空泵
vacuum pump
指示功率
indicated power
指示热效率
indicated thermal efficiency
指示油耗率
indicated specific energy consumption
示功图
indicator diagram
冷却系
cooling system
风冷
air cooling
水冷
water-cooling
循环流冷却系
cooling recovery system
自然循环液冷却系统
natural circulation type cooling system
热流循环液冷却系统
thermo-siphon circulation type cooling system
温差循环液冷却系统
gravity circulation water cooling system
压力式水冷却系统
positive circulation cooling system
加压式冷却法
pressure type cooling
水泵循环冷却系统
pump circulation cooling system
强制循环式化冷系统
forced-feed water circulation system
封闭式液冷系统
sealed cooling system
散热器
radiator
片式散热器
finned radiator
管式散热器
tubular radiator
蜂窝式散热器
cellular radiator
哈里逊式散热器
Harrison type radiator
带板式散热器
ribbon type radiator
上水箱
upper tank
下水箱
lower tank
涨溢箱
expansion tank
散热器芯
radiator core
之字形管散热器芯
film core
管-片式散热器芯
fin and tube core
散热器加水口盖
radiator filter cap
压力式水箱盖
radiator-pressure cap
蒸气-空气泄放阀
vapor-air release valve
散热器护罩
radiator cowl
散热器百叶窗
radiator shutter
散热器保温帘
radiator roller blind
散热片
cooling fin
缸盖散热片
cylinder head fin
缸体散热片
cylinder block fin
控温装置
temperature regulating device
恒温器
thermostat
恒温器主阀
thermostat main valve
恒温器旁通阀
thermostat by-pass valve
恒温器挠性波纹筒
thermostat flexible bellows
液体冷却设备
liquid cooling equipment
水泵
water pump
水泵体
pump casing
水泵叶轮
water pump impeller
旁通进水口
water by-pass inlet neck
循环泵
circulating pump
主进水口
water main inlet port
出水口
water outlet port
自调式水封
self-adjusting seal unit
溢流管
overflow pipe
导流板
deflector
风扇
fan(blower)
轴流式风扇
axial flow fan
离心式风扇
centrifugal fan
风扇壳体
blower casing
风扇导流罩
fan cowl
风扇毂
fan hub
风扇叶片
fan blade
风扇叶轮
blower impeller
风扇导流定子
blower stator
风扇皮带轮
fan pulley
三角皮带
v-belt
风扇护罩
fan shroud
风扇叶轮叶片
impeller vane
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool..com / FAX:+886 4 2471 4839 N.Branch 5F,No.460,Fu Shin North Rd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,Taipao City,Chiayi Hsien,Taiwan
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、hss drill’Фрезеры’Carbide drill、High speed steel、Milling cutter、CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills、Stub roughing end mills、Dovetail milling cutters、Carbide slot drills、Carbide torus cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot drills、Mould cutter、Tool manufacturer.
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（７）医療用品エンド・ミル設計
弊社の製品の供給調達機能は：
（４）オートメーション整備調達
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
BW специализируется в научных исследованиях и разработках, и снабжаем самым высокотехнологичным карбидовым материалом для поставки режущих / фрезеровочных инструментов для почвы, воздушного пространства и электронной индустрии. В нашу основную продукцию входит твердый карбид / быстрорежущая сталь, а также двигатели, микроэлектрические дрели, IC картонорезальные машины, фрезы для гравирования, режущие пилы, фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки форм для шлицевого вала / звездочки роликовой цепи, и специальные нано инструменты. Пожалуйста, посетите сайт www.tool-tool.com для получения большей информации.
BW is specialized in R&D and sourcing the most advanced carbide material with high-tech coating to supply cutting / milling tool for mould & die, aero space and electronic industry. Our main products include solid carbide / HSS end mills, micro electronic drill, IC card cutter, engraving cutter, shell end mills, cutting saw, reamer, thread reamer, leading drill, involute gear cutter for spur wheel, rack and worm milling cutter, thread milling cutter, form cutters for spline shaft/roller chain sprocket, and special tool, with nano grade. Please visit our web www.tool-tool.com for more info.
No comments:
Post a Comment